Tempe Field

This data field displays data from Tempe sensor for devices that do not natively support it. ## Features - Tracking average, current, min and max temperatures that are displayed in Garmin Connect - Showing the battery level upon start - Supports the ability to set a temperature offset that will be applied for the Tempe sensor data - Switching between min/max 24 hour, current, activity min/max/avg temperatures and battery level by tapping on the field (only for Edge touch screen devices) - Supports pairing multiple Tempe sensors (up to three) ## How to use 1. Download the data field application from Garmin Connect Store and synchronize your Garmin Edge 2. Select the data screen where you want put the data field 3. On the chosen field select "Connect IQ" - "Tempe Field" 4. Place Tempe sensor near Edge and the temperature should be displayed on the screen (this should take up to 15 seconds) ## Unpair Tempe sensor After the Tempe sensor is connected to Edge, its device number will be stored in the "Tempe device number" app-setting. In case you want to pair a different Tempe sensor, you need to reset "Tempe device number" app-setting by setting the value to "0". This can be done by using either Garmin Express or Garmin Connect Mobile. ## Pair multiple Tempe sensors By default only one Tempe will be paired in order to prevent pairing Tempe sensors from other people when our is off. To pair an additional Tempe sensors: 1. Update "Second Tempe device number" app settings value from -1 to 0 2. Make sure that the Tempe sensor that was already paired is far away from Garmin Edge 3. Wait until the battery level is displayed (this can take up to one minute) ## Tracking delay By default, minimum, maximum, and average temperatures are only updated when the timer is running. However, at the beginning of the activity, the Tempe sensor may not show an accurate temperature due to the drastic temperature changes (e. g. moving Tempe from a house/garage to outside). Therefore, it is possible to set a delay preventing updating min/max/avg temperatures. The delay will also be used when the activity is paused or stopped. When the activity is resumed, the data field will calculate the delay based on the set delay and the time the timer was paused/stopped. For example, if the delay is set to 15 minutes and the timer is paused for one minute (e. g. red light stop), the delay will only be one minute. If the timer is paused for more than 15 minutes, the delay will be 15. In short, the delay when the timer is resumed will be up to the delay set in the configuration. ## Error codes In case an invalid combination of settings is selected or there an issue with the ANT channel, an error will be displayed on the screen. The following errors can be displayed: - Error 1: An error occurred while trying to initialize the ANT channel. Check that this data field is the only Tempe data field displayed. - Error 2: The initialized ANT channel could not be opened. Check that this data field is the only Tempe data field displayed. - Error 3: The field layout positions were not found. - Error 4: None of the predefined battery icons fit on the screen. This error will be shown only when there is a bug in the layout.

Version 1.3.16: - Added support for Venu X1 Version 1.3.15: - Added support for Forerunner 970 Version 1.3.14: - Fixed "Display label" app setting for watches Version 1.3.13: - Added "Display label" app setting Version 1.3.12: - Optimized label text positioning for Fenix 8 47mm with 6 Fields Layout Version 1.3.11: - Optimized label text positioning for Fenix 8 47mm with 7 Fields Layout Version 1.3.10: - Changed temperature chart color to the one used by the native field (gray) Version 1.3.9: - Fixed transparent background for newer devices Version 1.3.8: - Added support for fenix 8, Enduro 3, Forerunner 165, Venu 3 and Instinct 2 Version 1.3.7: - Added support for Edge 1050 Version 1.3.6: - Fixed Error 3 issue on Edge 1040 Version 1.3.5: - Added support for fenix 7 Pro and Epix Pro Version 1.3.4: - Use transparent background Version 1.3.3: - Added support for Enduro Version 1.3.2: - Added support for Edge 540 and 840 Version 1.3.1: - Fixed displaying the battery level for a very short duration at start Version 1.3.0: - Added the ability to delay updating min/max/avg temperatures Version 1.2.0: - Added the ability to pair multiple Tempe sensors Version 1.1.0: - Added support for fenix and forerunner devices