Moonphase Chrono

For those die-hard analog chronograph lovers, myself included. This watchface features an uncluttered, easy to read design. # Features * Analog time * 3 subdial layout * Moon phase shown in lower subdial (northern or southern hemisphere display based on GPS position) * Left sub-dial configurable to: Heart rate as % of maximum Heart rate Battery % Today's step progress to goal % Today's activity minutes progress to goal % This week's activity minutes progress to goal % Current temperature * Date hand * Configurable hour and minute hand color * Outer arc can be set to be a move indicator, battery%, heart rate as % of max or goal progress indicator * Battery saving mode * Anti-aliased graphics (if supported by watch model) * Burn-in safe, full screen, always on display for AMOLED displays (with electable brightness level) NOTE: When the sub-dial reads 0% or a very small value, a black circle appears in the center of the dial hand (like a zero). This is to distinguish it from a 100% reading. # PRO Version features * Roman numeral hour number option * 3D (spherical) moonphase option * Configurable hour number color * Configurable second hand color * Configurable subdial pointer color * 4th subdial display option * All subdials can be configurable * Additional selections for subdials: Today's active calories burned progress to goal % Distance run/walked Floors climbed Meters (or feet) climbed METs (Metabolic Equivalent of Task) (during an activity) MET·hrs today MET·hrs/week Recovery time (hours) Body battery Stress level Feels like temperature Probability of precipitation Sea level barometric pressure [kPa] Windspeed (customizable units) Wind bearing Altitude 2nd time zone or UTC time Lunar cycle [days] (bottom subdial only) Moon illumination [%] 　 Sunlight hours (shows sundial like graphic with 24 hour current time pointer) NOTE: Not all selections are available on all watch models depending on hardware support NOTE: If the bottom subdial is set to sunlight hours, then the sundial like graphic will be shown during daylight hours, and the moonphase graphic will be shown during nighttime hours. An orange arc on the subdial circumference indicates daylight hours when the moonphase complication is shown. * Directional heading compass indicator (when a GPS signal is available) * Sunrise and sunset time markers on the dial * Chronograph reset emulation: (shows second hand in 0 position in low power mode) * Always on second hand option (for Forerunner 255 and 955 series, Legacy Saga and Legacy Hero series, Vivoactive 4/4S, Approach S62 and Fenix 7/7S/7X models only) * Bonus: replica mode # Payment For the PRO version, use this link to pay US$2.99 via Stripe (no account required; credit card, Apple Pay, Google Pay accepted). https://buy.stripe.com/dR68ybaEkbJ37wAeXF Alternative payment via Paypal: https://www.paypal.com/paypalme/trudelta/2.99USD Important instructions to get your unlock code quickly: https://ko-fi.com/post/Payments-via-PayPal-Z8Z6AIK78 If you don't get a reply within 8 hours, see here for help: https://ko-fi.com/post/Common-causes-for-not-receiving-your-unlock-code-N4N8BUEGH # Tags Chronometer, chronograph, analog, moon phase

Version 0.22.0 Corrected crash on D2 Bravo and Fenix 3 models. Version 0.21.0 Reduced battery consumption. Version 0.20.0 Corrected crash if birth year setting value is not available. Minor optimizations. Version 0.19.0 Made performance and memory optimizations. Version 0.18.2, 0.18.3 Added support for the Enduro 3 and Fenix 8 series. Version 0.18.1 Added missing support for the Enduro 2. Version 0.18.0 Corrected crash on some models when entering AOD mode. Version 0.17.0 Changed AOD mode display for newer AMOLED display models (Connect IQ 5.0.0 or higher) to try to prevent flickering. Version 0.16.0 PRO version only change: Revised the MET-h/wk and MET-h today calculation. Version 0.15.1 Added support for Forerunner 165 models. Version 0.15.0 PRO version only change: Corrected the subdial lable for wind direction. Version 0.14.7 PRO version only change: Corrected description for the wind direction data selection. Version 0.14.6 Added support for the Descent Mk3 43mm models. Version 0.14.5 Added support for the Fenix 7 PRO Solar. Version 0.14.4 Added support for the Descent Mk3 model. Version 0.14.3 Added support for the Fenix 7X PRO Solar. Version 0.14.2 Added support for the Vivoactive 5. Version 0.14.1 Added support for Venu 3 series. Version 0.14.0 PRO Version only changes: Added option for 3D (spherical) moonphase as opposed to the traditional bosom moonphase complication. Added option to display only the moonphase in the lower subdial (no subdial pointer or scale) Version 0.13.2 Added support for Epix PRO and Fenix 7 PRO models. Version 0.13.1 Added support for Approach S70 series. Version 0.13.0 PRO Version only change: Added option to show moon % illumination on the subdials. Version 0.12.1 Added support for Forerunner 965 series. Version 0.12.0 PRO version only changes: Corrected display when always on seconds is enabled and battery save during sleep was active. Version 0.11.2 Added support for Forerunner 265 series. Version 0.11.1 Corrected date pointer on 390x390 and 320x320 pixel display devices. Version 0.11.0 PRO version only changes: Added option for Roman numeral hour numbers. Added option to force day of week display to English. Version 0.10.0 Corrected anomaly in the graphics for 416x416 pixel displays. PRO version only change: Changed label for the sunlight hours subdial display from "SUN" to show the day of the week. Version 0.9.0 PRO version only change: Added Sunlight hours (sundial-like) display option. NOTE: If the bottom subdial is set to sunlight hours, then the sundial like graphic will be shown during daylight hours, and the moonphase graphic will be shown during nighttime hours. Version 0.8.0 PRO version only change: Simplified second hand for always on seconds to attempt to fix drawing problems on some devices. Version 0.7.0 Changed progression of moon illumination for southern hemisphere locations. Decreased the width of the date hand. PRO version only change: Fixed overlap of labelling for lunar cycle subdial display. Version 0.6.0 Changed color for moon and stars on MIP displays. Added support for 218x218, 360x360, 320x360 and 280x280 pixel devices. PRO version only change: Corrected wind bearing subdial tick marks. Version 0.4.0 Added support for 240x240 and 260x260 pixel devices. Version 0.3.0 Added support for 390x390 pixel devices. PRO version only change: Added lunar cycle to bottom subdial options.