BigFont eBike (Ant+ LEV and PWR)

BLINKING: It is 'normal' at startup for around 10 seconds. seems to be an error of Garmin, not of my implementation! The bike (Fazua Ride 60) uses to ANT+ interfaces to send data wireless to devices like a Garmin watch or to your Smartphone. - ANT PWR (Bicycle Power) sending RiderPower [W] , Cadence [Rev] ) etc - ANT+ LEV (Light Electrical Vehicle) sendig Battery [%], Assist [%] etc The data for my datafield is sent the following way: "ANT+ PWR" sendsTo "Garmin API" sendsTo "BF eBike datafield" "ANT+LEV" sendsTo "BF eBike datafield" An ANT+ interface can only be conneted to one device! So in this case: ANT+PWR must be connected via the "Sensor" menu of Garmin, so that its API (software) can get the values. Sensor ist shown as "PWR....xx" on the Garmin watch ANT+ LEV interface must be DISCONNECTED because my eBike datafield connects directly to the Fazua and uses not the internal Garmin API, as it is not available for a datafield. Sensor ist shown as "eBike....xx" on the Garmin watch Best is to disable Bluetooth on your Smartphone, start the datafield (by its activity) and then power up your bike. ... and in your activity there should be only one (this) datafield using ANT+ LEV connection! Please test the DatField before making the payment at https://paypal.me/Seli17/5EUR , then send me the displayed ID from the watch, the type of watch and your country. It is a manual process, but I reply as soon as possible (less than 24 hours). Thank you very much. ENJOY Hope you succeed!! Please feedback! in addition to my "BigFont MT Bike" App shows: ANT+ PWR: - RiderPower [W] as [RidW] - ANT Cadence [Rev] ANT+ LEV Sensor: - Batterie%, - Assist% (useless on Fazua Firmware 009 (should be corrected with 010) and Spezialized so far) - Motor Power [MotW] out of Power end LevAssist%. (does not work with Fimware Fazua 009) = levCurrentAssistLevel% * CurrentRiderPower / (100-levCurrentAssistLevel%) Default view: On main picture: Altitude Motor Power | Biker Power Battery % Known compatible Bikes so far: - Fazua Ride 60 (Focus JAM2 SL) - Specialized Levo Does not work on my - Shimano EP801 (Bulls Sonic EVO AM-SL) with Shimano SX-EM8000

2026-04-26: Vertical Speed chart in GC: only ONCE 2026-04-12: Use DATA_TYPE_UINT16 instead of Float FIT Rider and Motor charts: 2026-04-11: FIT Rider and Motor charts:save data also when not active on watch 2026-04-09: FIT Rider and Motor charts linitet at 0 to 450 W. Edge 540 added SDK 9.1.0 2026-03-22: FIT charts for motor and rider power finally fixed (missed Resources.xml) 2025-05-12: try to add FIT fields for motor and rider power and reduce logmessages on output file on the watch, so important messages are shown 2025-04-18: show ManufacturerID at Top when it is selected. 2025-04-09:Remove Fenix 6 as it has not enough memory adjust design of 6XPro and others. Format currentspeed gt "19.9" then round "20" SDK Connect IQ 8.1.1 2025-04-04: Added Edge 840 (and some imrovements in code) 2025-01-25: MotorPower with Bundle 10 now OK (?). Load settings OnStart() (avoid to exit and reenter the application) 2024-10-18: Formated Middle-Items 2024-09-05 added Fenix8 47mm and 51mm (non-AMOLED) 2024-05-01: Try to avoid blinking when Activity is not started 2024-04-18: Added Fenix 5X and 5X Plus. Garmin SDK 7.1